Zero Delay USB Gamepad Encoder for Switch/PC/PS3 - Arcade Joystick Controller

Product Description

Include: 1x Macro Encoder Board, 1x USB Cable, Multiple cables for buttons and joysticks. Include: 1x Macro Encoder Board, 1x USB Cable, Multiple cables for buttons and joysticks. 1. Press and hold the Macro button until the Macro LED flashes to start editing the Macro command. 2. Enter the key combination sequentially. (1) Available buttons: A, B, X, Y, L1, L2, L3, R1, R2, R3, SE, ST. (2) Available joysticks: up, up-left, left, down-left, down, down-right, right, up-right. (3) The key value is output at a fixed rate, and the time interval for inputting the key value is not recorded. 3. Short press the Macro button, the LED stops flashing, and the recording is successful. 4. Press the Macro button to sequentially output the recorded key combination. 1. Press and hold the Macro button until the Macro LED flashes to start editing the Macro command. 2. Enter the key combination sequentially. (1) Available buttons: A, B, X, Y, L1, L2, L3, R1, R2, R3, SE, ST. (2) Available joysticks: up, up-left, left, down-left, down, down-right, right, up-right. (3) The key value is output at a fixed rate, and the time interval for inputting the key value is not recorded. 3. Short press the Macro button, the LED stops flashing, and the recording is successful. 4. Press the Macro button to sequentially output the recorded key combination. 5. For example: (1)Press and hold the Macro 1 button until the light flashes. (2)Press in sequence: left, down-left, down, A, B. (3)Short press the Macro 1 button, the indicator light stops flashing. (4)Then, short press the Macro 1 button, the encoding board will output left, down-left, down, A, B in sequence. 5. For example: (1)Press and hold the Macro 1 button until the light flashes. (2)Press in sequence: left, down-left, down, A, B. (3)Short press the Macro 1 button, the indicator light stops flashing. (4)Then, short press the Macro 1 button, the encoding board will output left, down-left, down, A, B in sequence. 6. SOCD (Simultaneous Opposing Cardinal Directions): Preset 5 different SOCD modes. Select the mode you want, hold down the X, A, B and Y button, then press the select button once. The LED blinks a few times and then turns off, and the setting is successful. 6. SOCD (Simultaneous Opposing Cardinal Directions): Preset 5 different SOCD modes. Select the mode you want, hold down the X, A, B and Y button, then press the select button once. The LED blinks a few times and then turns off, and the setting is successful. (1) Button X + Select: ←+→=→, ↓+↑=↑, ←+↓+→=↓. (2) Button A + Select (default. Applies to most situations.): ←+→=None, ↓+↑=None, ←+↓+→=↓. (3) Button B + Select: ←+→=→, ↓+↑=↑, ←+↓+→=(down-right). (4) Button Y + Select: ←+→=None, ↓+↑=↑, ←+↓+→=↓. (5) Button L1 + Select: ←+→=←, ↓+↑=↑, ←+↓+→=↓. (1) Button X + Select: ←+→=→, ↓+↑=↑, ←+↓+→=↓. (2) Button A + Select (default. Applies to most situations.): ←+→=None, ↓+↑=None, ←+↓+→=↓. (3) Button B + Select: ←+→=→, ↓+↑=↑, ←+↓+→=(down-right). (4) Button Y + Select: ←+→=None, ↓+↑=↑, ←+↓+→=↓. (5) Button L1 + Select: ←+→=←, ↓+↑=↑, ←+↓+→=↓. 7. Separate D-pad/X-input switch buttons are compatible with all older games. Press and hold the button for 5 seconds, The encoder will switch to the next working mode, PC/PS3, Xbox 360 for Windows. 8. Press A+Turbo/Clear at the same time to set multiple clicks of the A button. Simplified operation. Press A+Turbo/Clear again to cancel. 9. Make sure to open Pro Controller Wired Communication on the Nintendo switch settings page when it work on Nintendo Switch 10. The firmware can be upgraded on the computer through the USB interface. 7. Separate D-pad/X-input switch buttons are compatible with all older games. Press and hold the button for 5 seconds, The encoder will switch to the next working mode, PC/PS3, Xbox 360 for Windows. 8. Press A+Turbo/Clear at the same time to set multiple clicks of the A button. Simplified operation. Press A+Turbo/Clear again to cancel. 9. Make sure to open Pro Controller Wired Communication on the Nintendo switch settings page when it work on Nintendo Switch 10. The firmware can be upgraded on the computer through the USB interface.